Simple 'all-in-one' heighting, diameter & log volume instrument with data storage.

150m/ 500’ reflectorless range, range finder, subtended distance,
missing distance, three point heighting, area, volume and rapid fire
modes. This unit stores up to 2000 measurements within its onboard
memory. Bluetooth data output. Supplied with soft bag, manual
CD, battery & charger, and wrist strap

LaserAce® Hypsometer (a Pocket Series Instrument) was designed to help foresters and arboriculturists easily and efficiently measure the height of a tree, its diameter (at any height on the tree), simple or ‘taper’ log volumes and tree lean. It is the only product on the market that has all these features in one single unit!

The LaserAce® Hypsometer incorporates an onboard multifunction computer. This computer stores results (up to 2000 trees) for later viewing and or downloading to PCs or PDAs using its onboard Bluetooth® (or RS232) data link. Providing users with a cableless data storage out in the field.

The internal ‘forestry’ software automatically carries out mathematical calculations for instant field results.

LaserAce® Hypsometer is simple to use with selectable modes to suit the required role.

What can it do?

Measure ranges
The LaserAce® Hypsometer will measure ranges up to 150m/ 500’ without a reflective target. Used with a prism (reflective target) the unit can measure up to 600m/ 1000’

Measure Diameters
The LaserAce® Hypsometer incorporates specially designed (x 5 magnification) stadia hairs. During operation, these (numbered) stadia hairs are used to bracket either side of a tree trunk. On firing the laser, the user can determine the correct diameter of the tree (at any point).

Measure height, lean and volume

The LaserAce® Hypsometer incorporates three different methods for measuring heights depending on the users requirements.

1. Single Point – point and shoot at the top of the tree – the LCD screen at the side of the unit will display the results. Used if tree is located on a flat plain ie. Park within a built up area
   

2. 2-Point height – this mode is used for remote calculation of height and distance between two successive points. The user just points and shoots at the base of the tree then at the top of the tree. The unit again shows the height on the LCD screen. This mode will also calculate the tree’s lean and volume (the user can enter a taper factor if required for more accurate volume measurements)
   

3. 3-Point height uses one laser measurement to the middle of the tree then two-angle measurements. This method is ideal if scrub is an issue at the base of a tree and/ or the leaves are too thin at the top (or merge with other trees so you can’t see the top). Other modes/ options
   

Brush filter mode (for use with reflective tape). If you require a range to a specific tree/ object activate the ‘brush filter mode’. This mode enables the laser to only pick up reflective prisms.

Critical range gating for area plots, add in a maximum distance and the LaserAce® Hypsometer want measure outside that specified target range.

Critical height/ diameter This mode allows users to enter the taper factor of a tree and 'find' the height at which a specified diameter is reached or the point up a tree at which a specified height or length is reached.

The unit has been designed for simple, effortless use – point-and-shoot technology. No need for bulky accessories, targets or responders. Simple ‘all-in-one’ heighting, diameter, lean and log volume instrument, affording users considerable cost savings on field operations.

Laser

• Class 1 eye safe laser distance meter (IEC / FDA)
• Passive range upto 150m/ 500ft
• Range to reflector 600m/ 1970ft
• Typical accuracy 5cm/ 2"
• Resolution 1cm/ 0.4"
• Measurement time 0.3 seconds

Environmental

• Operating temperature -10°C to +45°C
• Water & dust resistant (IP63)

Inclinometer

• Type: Accelerometer
• Range -70*° to + 70°
• Accuracy 0.1° at 0°
• Resolution 0.1°

Physical

• Data I/ O: Bluetooth® or RS232
• Weight: 400g/ 14oz
• Dimensions: 110mm x 100mm x 50mm/ 4.33" x 3.94" x 1.97"